Page 1 of 1

#1 Headphone amp ?

Posted: Thu Jul 10, 2008 11:16 am
by pre65
Hi-i am not really into headphones,but i might want to in the future.

Can i use the output from a DAC to feed headphones,or failing that the output from a valve pre ?

If so how ?

#2

Posted: Thu Jul 10, 2008 11:07 pm
by RSC
Hi Philip,

Output from a DAC: assuming you have a volume control here (otherwise, you'd be flat out volume all the time), you'd need a "two phono plug to jack socket" lead to make the connection and then you'd need to look at the headphones' impedance and how that would react with the DAC o/p voltage and o/p impedance.

Output from valve pre-amp: you've got the volume control, but still similar issues re. connections and electrical characteristics.

Unless you're talking Stax or similar, with their own energiser/pre-amp.

Be better to buy a cheap h/p amp (Creek, Project) or build one (WD do a valve kit), I'd have thought...

#3

Posted: Wed Mar 18, 2009 1:57 pm
by kuroguy
Phil,
If you want to try headphones I recommend you build the Starving Stdent Headphone amp (assuming you can source the 19J6 tubes). It can be built for beer money and sounds great. If you can't find 19j6 tubes you could always use 6j6 and substitute resistors for the tube heaters in the MOSFET load. you would need a slightly bigger power supply and a egulator or big resistor to drop the voltage for the 6 volt heaters. I'd do both heaters in series if I used 6j6. In fact, I plan to grab up a bunch of 6j6 for when I run out of 19J6.

#4

Posted: Thu Mar 19, 2009 4:49 pm
by Ali Tait
You could just buy a Beresford.The new 7520 is supposed to have a cracking headamp.

#5

Posted: Thu Mar 19, 2009 4:51 pm
by Ali Tait
You could just buy a Beresford.The new 7520 is supposed to have a cracking headamp.

#6

Posted: Sun Mar 22, 2009 9:04 am
by little eddy
Another cheap hybrid design using 12V supply and uses a 12AU7: http://diyaudioprojects.com/Solid/Tube- ... phone-Amp/

#7

Posted: Thu Dec 03, 2009 11:41 am
by labiteena
How can I convert a sony ericson headphone , to connect it to my lap top and use it for skype?? I bought a sony ericson headphone, without realing it was for the mobile phone. Is there any wire of some sort that could connect to my laptop the plug from the headphone( and mic combination) , which is compatible with a socket in the mobile but not the laptop.
___________________
yahoo keyword tool ~ overture ~ traffic estimator ~ adwords traffic estimator

#8

Posted: Thu Dec 03, 2009 1:42 pm
by Nick
Depends on the connector that is on the headphones. You would normally need to get the headphone to end in a pair of 3.5mm jacks.

#9

Posted: Fri Dec 04, 2009 3:59 am
by kuroguy
Was thinking about this phil. build a mosfet source follower and feed it with your valve preamp. You should be able to do that for under $30. If you don't like it your down side is $30 and you learned about source followers in the process. You can feed the 3 channel version with a pair of cheap switching supplies. +- 12 volts works well.

http://phonoclone.com/diy_sze.html

#10

Posted: Wed Jun 15, 2011 12:18 pm
by rainy22
As we all know that the most famous magic sound of Monster, the highest rate on the mirror is the Monster Studio headphones, NBA star,U.S. singers use this product, go to search it in Baidu or Google,choose their best one.

#11

Posted: Wed Jun 15, 2011 12:56 pm
by shane
rainy22 wrote:As we all know
Do we?

#12

Posted: Wed Jun 15, 2011 2:33 pm
by pre65
rainy22 wrote:As we all know
Not me sunshine. :wink: