Page 1 of 9

#1 yet another boring one trick pony turntable build

Posted: Mon Oct 08, 2018 9:45 pm
by Ant
ive been building something again.
a little different to my usual, but not by much.
i had a lenco gl59 hanging around doing nothing, so ive done what phil did years ago and chopped it down into a motor unit.

from this....

ImageMake your own g88 by anthony cresswell, on Flickr

to this

ImageMake your own g88 by anthony cresswell, on Flickr

painted it black initially but i didn't like it so i did it matt white instead.

#2 Re: yet another boring ssdd turntable build

Posted: Mon Oct 08, 2018 9:49 pm
by Ant
the motor was seized up and the spindle was rusty so its been rebuilt. looked like this

ImageMake your own g88 by anthony cresswell, on Flickr

i put the rotor in the lathe and spun it up, i used some polishing compound to clean it all up without using an abrasive that would damage the taper by being too coarse. now looks like this

ImageMake your own g88 by anthony cresswell, on Flickr

also did the bearing spindle in this way as it was a little ropey.

#3 Re: yet another boring ssdd turntable build

Posted: Mon Oct 08, 2018 9:52 pm
by Ant
i also stripped the white platter and repainted it black to contrast with the white chassis

ImageMake your own g88 by anthony cresswell, on Flickr

then made a laminate plinth

ImageMake your own g88 by anthony cresswell, on Flickr

#4 Re: yet another boring ssdd turntable build

Posted: Mon Oct 08, 2018 9:59 pm
by Ant
did a load of routering, and hacked the actual plinth out of the rough glued up block

ImageMake your own g88 by anthony cresswell, on Flickr

then offered up the deck and the project 9cc arm wot i bought for it

ImageMake your own g88 by anthony cresswell, on Flickr

#5 Re: yet another boring ssdd turntable build

Posted: Mon Oct 08, 2018 10:05 pm
by Ant
on offering it up, the arm needed to be lower so ive hacked out a deeper section than usual for the arm board.

ImageMake your own g88 by anthony cresswell, on Flickr

it was going to be 12mm deep so that the arm board wold sit flush with the top, as it is, it is 24mm deep instead so that the arm will be recessed by half an inch when the board is in, same as the 99 i did for neal.

while i was doing this, i managed to lose my wedding ring..... shook my arm to clear a load of dust off my overalls and it shot off my bloody finger.....

took an hours frantic searching to to find it, and ended up with all the geraniums ripped out. it was in a clump of them.....

shan't do that again

#6 Re: yet another boring one trick pony turntable build

Posted: Tue Oct 09, 2018 12:27 pm
by Mike H
FAB!! Image

Yep black on white works. Image

Oh sorry, "shoddy!" :D

#7 Re: yet another boring one trick pony turntable build

Posted: Tue Oct 09, 2018 12:29 pm
by gninnam
Nice work - very clean 8)
I lost my wedding ring 2 days after being married - never replaced it (wife was Ok with this as I never wore jewelry before I was married) :wink:

#8 Re: yet another boring one trick pony turntable build

Posted: Tue Oct 09, 2018 7:37 pm
by Ant
more routering and the plinth machining is now all done.

i took the arm board cutout further forward to clear the arm rest and made it look ok by cutting it in line with the speed marker.

and added a toggle switch for power

ImageMake your own g88 by anthony cresswell, on Flickr

next, arm mounting board needs making...

onwards!

#9 Re: yet another boring one trick pony turntable build

Posted: Wed Oct 10, 2018 12:07 am
by Mike H
'Allo 'allo, it couldn't resist? :lol:

https://flic.kr/p/2byQtRb

#10 Re: yet another boring one trick pony turntable build

Posted: Sun Oct 14, 2018 4:04 pm
by Ant
got a load more done, got the plinth painted to seal it all before veneer and an arm board made

ImageMake your own g88 by anthony cresswell, on Flickr

the arm board is a piece of solid oak with a walnut veneer applied to the top face. This was then drilled to accept a set of rubber decoupling grommets.

then got the veneer applied

ImageMake your own g88 by anthony cresswell, on Flickr

and a couple of other shots with a g99 lurking in the background. next job.

ImageMake your own g88 by anthony cresswell, on Flickr

ImageMake your own g88 by anthony cresswell, on Flickr

ImageMake your own g88 by anthony cresswell, on Flickr

that nasty cap was the spark surpressor cap. it was knackered.......

#11 Re: yet another boring one trick pony turntable build

Posted: Sun Oct 14, 2018 5:56 pm
by Ray P
Looking good Ant. You must be pleased.

#12 Re: yet another boring one trick pony turntable build

Posted: Mon Oct 15, 2018 7:10 pm
by Ant
bit more done on it, though not through choice.
i was inclined to keep the walnut in its bare colour, but that was not to be as son number one managed to get something on the veneer that marked it.

in the end i had to darken the finish to even it all out. This was the idea in the first place, but i kinda liked the contrast between the black top and the wood.

have some matt clear coat on the way to go over it all to seal it

ImageMake your own g88 by anthony cresswell, on Flickr

it does however focus the eye on the motor unit.....

#13 Re: yet another boring one trick pony turntable build

Posted: Sat Oct 20, 2018 3:15 pm
by Ant
all done

took some fettling to get the finish right, its had a matt clear lacquer over the top of everything so that the change from veneer to paint from the sides to to edge is seamless.

ImageMake your own g88 by anthony cresswell, on Flickr

the project arm is very nice, a ruddy bargain for what i got it for. has the boring goldring cart in it at the moment as i wasnt going to disturb the at150 for now.

ImageMake your own g88 by anthony cresswell, on Flickr

this was to check for rumble ect but it sounds ok in this arm, although the project seems to be set up for heavier carts as its had to have a shim put on the top to add some weight and make it balance out properly

ImageMake your own g88 by anthony cresswell, on Flickr

can see the contrast between the veneer and the black.

well pleased

edit: she who must be obeyed has said one of the decks must be sold as i now have too many apparently....... fergodsake....

#14 Re: yet another boring one trick pony turntable build

Posted: Sat Oct 20, 2018 4:20 pm
by antonio66
Yet another great job Ant.

#15 Re: yet another boring one trick pony turntable build

Posted: Sat Oct 20, 2018 6:00 pm
by Ant
Ta, wasn't as simple as it should have been, but got there in the end.

Im seriously having to think about what decks to keep though, SWMBO has allowed 3, one automatic for her, the jbe which I won't let go ever, and one other.

I do have 8 here though, I didn't think that was an unreasonable number but.............. :mrgreen: