Pete Millett ATEST

I think we all know by now what this section is for.
User avatar
pre65
Amstrad Tower of Power
Posts: 20786
Joined: Wed Aug 22, 2007 11:13 pm
Location: North Essex

#46 Re: Pete Millett ATEST

Post by pre65 »

Hi Max, good to see you around. :)

I use photobucket to show pictures and diagrams on here.
The only thing necessary for the triumph of evil is for good men to do nothing.

Edmund Burke

G-Popz THE easy listening connoisseur. (Philip)
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#47 Re: Pete Millett ATEST

Post by Max N »

Hi Phil
It's nice to be back, thanks :)
I'll try photo bucket - probably need to convert it from pdf to something else first. I'll have a play
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#48 Re: Pete Millett ATEST

Post by Max N »

I can't upload to Photobucket at the moment, I'll try to figure out what's up later. For now I think I'll just go and solder some bits :)
User avatar
pre65
Amstrad Tower of Power
Posts: 20786
Joined: Wed Aug 22, 2007 11:13 pm
Location: North Essex

#49 Re: Pete Millett ATEST

Post by pre65 »

I scanned your diagram, but like you I can't upload to Photobucket. :(
The only thing necessary for the triumph of evil is for good men to do nothing.

Edmund Burke

G-Popz THE easy listening connoisseur. (Philip)
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#50 Re: Pete Millett ATEST

Post by Max N »

OK thanks for trying anyway Phil
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#51 Re: Pete Millett ATEST

Post by Max N »

OK I remembered how to insert an image. I had to open an IMGUR account. Photobucket seems to be playing up.
Anyway, is this how I should wire up the misfits for over-current protection in place of the 49.9K resistors?
Thanks
Image
Andrew
Eternally single
Posts: 4200
Joined: Thu May 24, 2007 2:18 pm

#52 Re: Pete Millett ATEST

Post by Andrew »

I'll dig up the circuit for you, Max, give me a day or so.

Cheers,

Andrew
Analogue, the lost world that lies between 0 and 1.
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#53 Re: Pete Millett ATEST

Post by Max N »

OK, thanks Andrew, much appreciated :)
In the spirit of trying to figure things out for myself, I've had a read of the application note where I found the above diagram and I think I now know how this circuit works. :idea:
Depending on which way the current is flowing, one transistor is 'on' while the other acts as a current limiter.
The limiting current is approximately Vgs(th) / R1
For the BPS129, Vgs(th) is between -2.1 & -1.0V
So if R1 is 20R, the current limit will be between 105mA and 50mA
Below the current limit, the whole circuit behaves like a resistor of about 30R

If we used DN2540 instead, Vgs(th) is between -3.5 and -1.5V
So we could set R1 to 30R for similar current limit range....

How did I do? :)

It's been a while since I did anything like this, but I can feel the cogs grinding and starting to free up....
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#54 Re: Pete Millett ATEST

Post by Max N »

For anyone interested, the diagram comes from Supertex Application Note AN-D66
http://ww1.microchip.com/downloads/en/A ... AN-D66.pdf
I'll put a copy in the 'Stacks' area
Edit - can't put a copy in the stacks area, its too big
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#55 Re: Pete Millett ATEST

Post by Max N »

'Gratitude is the sign of noble souls' - Aesop
Andrew, just wanted to say thanks for all the other info you've shared about the Atest interface, it's been a big help in building mine.
Same goes to DTB, James, and both Nicks.
Cheers
Max
User avatar
jack
Thermionic Monk Status
Posts: 5134
Joined: Wed Dec 29, 2010 8:58 pm
Location: ɐılɐɹʇsnɐ oʇ ƃuıʌoɯ ƃuıɹǝpısuoɔ
Contact:

#56 Re: Pete Millett ATEST

Post by jack »

You could use the TO-92 rather than the TO-220 variant of the DN2540 for such a small current...
Vivitur ingenio, caetera mortis erunt
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#57 Re: Pete Millett ATEST

Post by Max N »

Yep, good idea, I'm still trying to decide how to do this neatly.
I'm thinking I might use BSP129s mounted on these
Image
I could use short links to join the boards together
Max N
Old Hand
Posts: 1409
Joined: Thu Aug 16, 2007 6:10 pm

#58 Re: Pete Millett ATEST

Post by Max N »

I decided to use some nickel-based spray-on shielding compound instead of copper tape and mu metal.
Hmmmm, my shed could do with a lick of paint.......
Image
Image
Andrew
Eternally single
Posts: 4200
Joined: Thu May 24, 2007 2:18 pm

#59 Re: Pete Millett ATEST

Post by Andrew »

Hi Max, should get to it later today, somewhere I have a photo, I think, of how James wired this up using the bsp parts without the expense of a PCB, it was a very neat solution. You could try a PM to James to set if he kept a copy?

Andrew
Analogue, the lost world that lies between 0 and 1.
Andrew
Eternally single
Posts: 4200
Joined: Thu May 24, 2007 2:18 pm

#60 Re: Pete Millett ATEST

Post by Andrew »

This is my circuit, it's simple enough.
bsp.png
Analogue, the lost world that lies between 0 and 1.
Post Reply