wad hd83
#1 wad hd83
hello all . i have a wad hd83 i have the circuit diagram but due to me being computer illiterate i cannot put it on here !! (you can leave the word computer out if you wish) cilin.hepburn has given me some advice (other forum) as i have the wrong power supply caps in ,and a choke would help the power supply . transformer diodes 205v 470uf 100r 200v 470uf 4.7k 100uf 190 v .. i have A E CHOKE that looks like an ideal candidate i think ita a mk 1.5 first board there was a change of resistor and some other part and i think it needs another resistor on the input . so if someone can help and put up the circuit dia mike h poss can help where to put the E CHOKE, polite its answers on her rude suggestions on a post card
dave
dave
#2 hd 83 headphone amp
http://www.world-designs.co.uk/acatalog/hd83.pdf
that i think is a link to the curcuit info i have juat done some voltage checks i dont think i have enough spare volts to put a choke in
dave
that i think is a link to the curcuit info i have juat done some voltage checks i dont think i have enough spare volts to put a choke in
dave
#3
Not entirely sure what you meant about wrong caps, but replacing r1 with a hammond 159Q choke should work fine.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
#4 hd83
wrong caps. as in it has been built 250volt caps for c1/c2 i think more safety margin is req ? i was hoping to use my E CHOKE as i have a couple of them but i think they drop volts by 20 i think that can be changed and a big plus it will fit in the case its a mk1 small steel caseNick wrote:Not entirely sure what you meant about wrong caps, but replacing r1 with a hammond 159Q choke should work fine.
thanks dave
- Mike H
- Amstrad Tower of Power
- Posts: 20189
- Joined: Sat Oct 04, 2008 5:38 pm
- Location: The Fens
- Contact:
#5
This is "our" E-choke is it? ![Very Happy :D](./images/smilies/icon_biggrin.gif)
If so then presume the 220k is reduced to 100k (as supply seems to be about 250V or less (?)
And yes needs a 10R 1 - 2W resistor adding in series with the input. The module will drop 24V
Finally found the connection diagram:
http://www.audio-talk.co.uk/phpBB2/view ... 4864#34864
![Very Happy :D](./images/smilies/icon_biggrin.gif)
If so then presume the 220k is reduced to 100k (as supply seems to be about 250V or less (?)
And yes needs a 10R 1 - 2W resistor adding in series with the input. The module will drop 24V
Finally found the connection diagram:
http://www.audio-talk.co.uk/phpBB2/view ... 4864#34864
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
#6
If you were buying them now, I would suggest 300v or above, but 250v will be fine, 205v across 250v caps is ok, 12% below max, so not worth fretting about IMHO.
Do you have a hum problem the echoke is to fix? As you say, I think you need more than 5v margin. I could be possible if the ripple at that point is only a volt or so P/P
Do you have a hum problem the echoke is to fix? As you say, I think you need more than 5v margin. I could be possible if the ripple at that point is only a volt or so P/P
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
#7
This is "our" E-choke is it? yes mike it is. 30v is to much !Nick wrote:If you were buying them now, I would suggest 300v or above, but 250v will be fine, 205v across 250v caps is ok, 12% below max, so not worth fretting about IMHO.
Do you have a hum problem the echoke is to fix? As you say, I think you need more than 5v margin. I could be possible if the ripple at that point is only a volt or so P/P
yes nick the thing is 1980s , so i am going to re cap it ,prob better diodes and resistors etc . but i can hear Maine's type hash, and all other post on this amp indicate that improved power supply helps
MICK H do you do an equvilant to hammond 159Q choke ! thiS is prob the simple answer to improve the amp
- Mike H
- Amstrad Tower of Power
- Posts: 20189
- Joined: Sat Oct 04, 2008 5:38 pm
- Location: The Fens
- Contact:
#8
Well there's what was the old Maplin ST28F, 10H, 100mA, 150 Ohms
Now coded VT495
![Question :?:](./images/smilies/icon_question.gif)
Now coded VT495
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
#9 hd 83 headphone amp
[quote="Mike H"]Well there's what was the old Maplin ST28F, 10H, 100mA, 150 Ohms
hello all. i fitted new power supply caps and fast diodes ,i a little better
then i put the choke in, i thought poss its resistance may be a bit high but no its all good, ht ok no smoke or fire ,and its made a BIG improvement
i think shielding the mains transformer from the output transformers
will also help( its all in a small steel shoe box )will aluminium sheet be ok ?![Question :?:](./images/smilies/icon_question.gif)
![Question :?:](./images/smilies/icon_question.gif)
hello all. i fitted new power supply caps and fast diodes ,i a little better
then i put the choke in, i thought poss its resistance may be a bit high but no its all good, ht ok no smoke or fire ,and its made a BIG improvement
i think shielding the mains transformer from the output transformers
will also help( its all in a small steel shoe box )will aluminium sheet be ok ?
![Question :?:](./images/smilies/icon_question.gif)
#10
Ali will be good to shield static fields. Is it a toroidal mains tx, if so, its always worth if you can to rotate it till the lowest him is produced. They tend to "spray" field from where the leads come out.
Whenever an honest man discovers that he's mistaken, he will either cease to be mistaken or he will cease to be honest.
#11
thanks nick. yes its a toroidal mains, with long leads so i can try rotating itNick wrote:Ali will be good to shield static fields. Is it a toroidal mains tx, if so, its always worth if you can to rotate it till the lowest him is produced. They tend to "spray" field from where the leads come out.
- Mike H
- Amstrad Tower of Power
- Posts: 20189
- Joined: Sat Oct 04, 2008 5:38 pm
- Location: The Fens
- Contact:
#12
FWIW I tend not to like steel cases as I've found it "conducts" the magnetic fields all over the place
Aluminium is preferred
Aluminium is preferred
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
-
- User
- Posts: 7
- Joined: Mon Mar 30, 2009 11:15 pm
#13
Hello
In my experience you will need to isolate the mains trany to reduce hum
In my experience you will need to isolate the mains trany to reduce hum
- Mike H
- Amstrad Tower of Power
- Posts: 20189
- Joined: Sat Oct 04, 2008 5:38 pm
- Location: The Fens
- Contact:
#14
If you mean remove it away from the amplifier, that's what I've discovered too.
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
-
- User
- Posts: 7
- Joined: Mon Mar 30, 2009 11:15 pm
#15
Well shield the O/P transformers from the mains transformer i.e. with an insulation plate (metal)