Another speaker thread

Dedicated to those large boxes at one end of the room
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#241 Re: Another speaker thread

Post by simon »

And this is the combined plot of all four drivers in the left speaker at the listening position using the x9 self averaged measurements:
All L 2m.jpg
All L 2m.jpg (108.07 KiB) Viewed 12405 times
For ease of reference this is the previous plot:
All 4 drivers 2m listening position ear adjusted.jpg
All 4 drivers 2m listening position ear adjusted.jpg (89.5 KiB) Viewed 12405 times
The 208 and T90 plots are reasonably different on the face of it.
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#242 Re: Another speaker thread

Post by simon »

I thought I'd investigate the variability of the measurements within the averaged reading, here's the SB sub:
SB Sub L 2m individual x9.jpg
SB Sub L 2m individual x9.jpg (89.73 KiB) Viewed 12401 times
This is the 285GMF:
285 L 2m individual x9.jpg
285 L 2m individual x9.jpg (98.22 KiB) Viewed 12401 times
The 208EZ:
208 L 2m individual x9.jpg
208 L 2m individual x9.jpg (104.13 KiB) Viewed 12401 times
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#243 Re: Another speaker thread

Post by simon »

And finally the T90A:
T90A L 2m individual x9.jpg
T90A L 2m individual x9.jpg (87.4 KiB) Viewed 12401 times
I'm not sure there are too many conclusions, other than small distances can count, and my room's probably a bit nasty for sound.
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#244 Re: Another speaker thread

Post by simon »

I'm not sure what to try next, but I think I might gaffer tape some cardboard to extend the baffle wings and remeasure to see if it has any affect, and if so what. I'm particularly interested to see if it changes the 285GMF response at all as they're a bit peaky.

I'm open to suggestions. Room treatment will be a consideration at some point I guess.
Ant
Shed dweller
Posts: 2332
Joined: Mon Jul 31, 2017 6:45 pm
Location: Yorkshire

#245 Re: Another speaker thread

Post by Ant »

Ive found since i did the last set of measurements on the fanes that shut curtains made quite abit of difference. the left hand side of the room appears more lively than the right, and that moving the footstool made a big difference, especially to the channel balance
Also starring Rex Hamilton as Abraham Lincoln

www.bte-designs.weebly.com
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#246 Re: Another speaker thread

Post by simon »

I'm sure you're right Ant - mine's an odd room: concrete floor over the garage, brick walls on 3 sides, stud on the right, crammed full of stuff as it's now my office/play room/storage facility. When I played around with a room mode calculator IIRC there were a few around 110Hz, and multiples of, that appear to be affecting the 285GMF in particular.

It would be interesting to drag it all downstairs to the living room so there was space behind the speakers as well as to the sides and front but it's a hell of a job, I'd need Pickfords.
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#247 Re: Another speaker thread

Post by simon »

Funnily enough I did some measurements of the right speaker also - all the previous were with the left speaker only.
All 2m L&R.jpg
All 2m L&R.jpg (107.94 KiB) Viewed 12385 times
This needs a bit of description, and it wasn't easy to show both left and right speakers on the same plot with enough detail - the reddy colour is the right speaker, the green the left.

The left speaker was measured first, then I measured the right starting with the T90A and worked down to the sub. But after the 208 when I started to measure the 285 I got feedback through the mic and had to reduce the measurement signal level a touch to stop it. So it's not a completely like for like comparison of the L and R plots of the SB sub and 285. Whilst the SB sub looks a little better perhaps the 285GMF has a rather horrid peak around 280Hz and another smaller around 130Hz.
chris661
Shed dweller
Posts: 2556
Joined: Mon Feb 22, 2010 7:29 am
Location: Sheffield

#248 Re: Another speaker thread

Post by chris661 »

Just a quick note that you really shouldn't be getting feedback, and that might be throwing all of your measurements out.

I can't remember which USB audio interface you're using, but anything like "monitor" or "direct monitor" should be off.

That switch feeds the inputs straight to the outputs so that musicians have a low-latency (the signal stays in the analogue domain) monitor feed so they can hear their mic/instrument (through headphones) when they perform.

Chris
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#249 Re: Another speaker thread

Post by simon »

Nuts. I wonder when that button was pressed. Only 100 odd measurements to repeat.

It's a Behringer thingy BTW.
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#250 Re: Another speaker thread

Post by simon »

It's taken me a little while to summon up the enthusiasm to redo the measurements but here they are. For simplicity I've only used REW's inbuilt 8 sweep averaging rather than do my own and average. And I only measured the Fostex 208Esigma and T90A as a combined "unit".

Here's the left channel:
All L 2m REW 8x ave.jpg
All L 2m REW 8x ave.jpg (116.37 KiB) Viewed 12029 times
And here's the right channel:
All R 2m REW 8x ave.jpg
All R 2m REW 8x ave.jpg (115.99 KiB) Viewed 12029 times
The plots suggest a falling response, and perhaps the SB29 subs could be turned down a little, and the 208&T90 up a touch. I don't feel this is required by listening to music though. The 208&T90 response in particular is a consequence of their directionality I suspect, more of which later.
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#251 Re: Another speaker thread

Post by simon »

Here's the average of the previous plots for the left and right channels
All L&R averaged.jpg
All L&R averaged.jpg (103.77 KiB) Viewed 12024 times
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#252 Re: Another speaker thread

Post by simon »

For a little fun here are plots of the left and right channels, a single measurement taken in front of the middle of my head compared to an 8 average of a centre reading and a further 7 taken on a circle c200mm radius.
All L 2m.jpg
All L 2m.jpg (101.8 KiB) Viewed 12024 times
All R 2m.jpg
All R 2m.jpg (102.17 KiB) Viewed 12024 times
This appears to support the theory of the directionality issue of the 208 & T90.
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#253 Re: Another speaker thread

Post by simon »

And a final plot of both channels, a single reading compared to a REW 8x average
All LandR 2m.jpg
All LandR 2m.jpg (101.84 KiB) Viewed 12024 times
Thoughts gratefully received. The response is a bit lumpy in parts, I'd guess a reflection of the room and the drivers themselves.
chris661
Shed dweller
Posts: 2556
Joined: Mon Feb 22, 2010 7:29 am
Location: Sheffield

#254 Re: Another speaker thread

Post by chris661 »

Simon,

When you say "8x average", do you mean you told REW to do multiple sweeps in the "Measurement" pop-up, or did you run the same sweep eight times (ie, clicked "measure" eight times, did 8x single sweeps) and average those?


Assuming the same mic position, I find the difference from 1x sweep to 8x sweeps to be very odd, and would be worthy of further investigation.

Chris
simon
Thermionic Monk Status
Posts: 5600
Joined: Thu May 24, 2007 11:22 am
Location: People's Republic of South Yorkshire

#255 Re: Another speaker thread

Post by simon »

REW did 8 sweeps then gave me the average, for each I positioned the mic centrally then 7 on a circle approx 200mm radius to give a less sensitised reading. I thought this was the thing to do?
Post Reply